DaliLoopeCommonControlCommandCodes Enumeration |
Enum to define DALI 3-byte Common Control Command Codes.
Namespace: Crestron.SimplSharpPro.LightingAssembly: Crestron.SimplSharpPro.Lighting (in Crestron.SimplSharpPro.Lighting.dll) Version: 2.21.121
Syntaxpublic enum eCommonControlCommandCodes
Members| Member name | Value | Description |
|---|
| QueryData | 0 |
Used to read data specified by the 3rd byte.
|
| QueryFeatureSupport | 1 |
Used to determine if a feature is supported or not.
|
| SetDtrX | 2 |
Used to set the DTR X register.
|
| SetDtrY | 3 |
Used to set the DTR Y register.
|
| SaveDataAtDtr | 4 |
Store "data" into memory location specified by DTR X/Y.
|
| ReadValueFromLocation | 5 |
Read memory location specified by DTR X. Use "data" as second pointer.
|
| AndDataIntoMemoryLocation | 6 |
"data" lists bits to clear in the memory location pointed by DTR X/Y.
|
| OrDataIntoMemoryLocation | 7 |
"data" lists bits to set in the memory location pointed by DTR X/Y.
|
| SetCg0GroupAssignmentForGroups0To7 | 8 |
"data" bits set '1' to join each desired group (groups 0-7).
|
| SetCg1GroupAssignmentForGroups8To15 | 9 |
"data" bits set '1' to join each desired group (groups 8-15).
|
| SetCg2GroupAssignmentForGroups16To23 | 10 |
"data" bits set '1' to join each desired group (groups 16-23).
|
| SetCg3GroupAssignmentForGroups24To31 | 11 |
"data" bits set '1' to join each desired group (groups 24-31).
|
| SetPbo | 12 |
Bank "0" is "normal operation", bank 1 is e.g. "after hours" operation if supported.
|
| SetPbrw | 13 |
"data" specifies the bank being written/read to/from.
|
| DataLessCommandContainedInData | 14 |
Dataless command contained in data.
|
| RestoreFactoryDefault | 15 |
"data" sets upper limit. All registers below or equal are reset to default values.
|
| SetOba0TwoByteControlOutputAByte1 | 15 |
Beginning Of Parameter Bank
|
| SetOba1TwoByteControlOutputAByte2 | 16 |
"data" contains second byte of inactive to active output A byte (ballast/actuator).
|
| SetObb0TwoByteControlOutputBByte1 | 17 |
"data" contains first byte of inactive to active output B byte (ballast/actuator).
|
| SetObb1TwoByteControlOutputBByte2 | 18 |
"data" contains second byte of inactive to active output B byte (ballast/actuator).
|
| SetThresholdValueA | 19 |
"data" contains desired A Threshold Value.
|
| SetThresholdValueB | 20 |
"data" contains desired B Threshold Value.
|
| SetDelayA | 21 |
Sets Delay A 15 Seconds Value in "data".
|
| SetDelayB | 22 |
Sets Delay B 15 Seconds Value in "data".
|
| SetRtRepeatInterval | 23 |
If non-zero repeat sensor output every "data" 15 seconds.
|
| SvSensorValue | 24 |
Actual sensor value sent in "data" using Controller Originator Addressing.
|
| SetSensitivity | 25 |
Setting of Controller sensitivity/range to the value defined in "data".
|
Version Information
.NET
Supported in: 6.0
.NET Compact Framework
Supported in: 3.5
See Also