Click or drag to resize

ChvTstatFcu Properties

The ChvTstatFcu type exposes the following members.

Properties
 NameDescription
Public propertyAuto1ptSetpoint Sets the auto1pt setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyAuto1ptSetpointFeedback Reports the active auto1pt setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with Auto1ptSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyAuto1ptSetpointLimitHighFeedback Property to report single-setpoint auto upper setpoint limit in tenths of current unit.

The BaseEvent event will trigger with Auto1ptSetpointLimitHighEventId for this property.

Public propertyAuto1ptSetpointLimitLowFeedback Property to report single-setpoint auto lower setpoint limit in tenths of current unit.

The BaseEvent event will trigger with Auto1ptSetpointLimitLowEventId for this property.

Public propertyAuto1ptSetpointLimitsDisable Property to disable setpoint limits on single-setpoint auto mode. True = Disable setpoint limits; False = Not Disable Setpoint limits
Public propertyAuto1ptSetpointLimitsDisableFeedback Property to indicate that setpoint limits on single-setpoint auto mode is disabled. True = setpoint disabled; False = setpoint not disabled

The BaseEvent event will trigger with Auto1ptSetpointLimitsDisableEventId for this property.

Public propertyAuto1ptSetpointMinus Lowers the temperature regulating setpoint for single-point auto only.
(Inherited from CresnetThermostat)
Public propertyAuto1ptSetpointPlus Raises the temperature regulating setpoint for single-point auto only.
(Inherited from CresnetThermostat)
Public propertyAutoDeadbandFeedback Reports the auto deadband value selected via the "db" option in the Setup menu, where 1d = 0.1 degrees. In dual-setpoint auto mode, this value is the minimum separation between heat and cool setpoints, which prevents the system from toggling back and forth due to overshoot. In single-setpoint auto mode, this value sets the hysteresis used when changing from heat to cool. For example, if the setpoint is 70°F with auto deadband of 2 degrees, the temperature would have to rise to 72°F before running cool, and 68°F before running heat. HZ-THSTAT reports auto mode deadband parameter in 10ths of current unit: Fahrenheit : 20, 30, 40, 50, 60 (F). Celsius : 10, 20, 30 (C).

The BaseEvent event will trigger with AutoDeadbandFeedbackEventId.


(Inherited from Thermostat)
Public propertyAUXBalancePoint Reports the auxiliary balance point in tenths of a degree. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyAuxHeatCallFeedbacks Returns a collection of components that indicate when the system is calling for auxiliary heat. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyColdWeatherComp Indicates that cold weather compensation has been enabled. The output remains true for as long as the mode is enabled. Outdoor low-temperature compensation modifies the humidifier output to prevent condensation on windows in cold weather.
(Inherited from CresnetThermostat)
Public propertyConnectedIpList A property containing the list of the ConnectedIpInformation objects which contain information about the devices that are connected to this IP ID. This property is only valid for an ethernet device. If this is not an ethernet device, then this property will return null. If this is an ethernet device, the list will be non-null. It will be empty if no devices are connected. The order of items in this list is not guaranteed.
(Inherited from GenericDevice)
Public propertyCoolAnticipator Reports the cool anticipator values, from 1 to 6. Prevents overshooting the set temperature. A lower number signifies more frequent cycles and faster response (tighter regulation), while a higher number signifies less frequent cycles and slower response (looser regulation).
(Inherited from CresnetThermostat)
Public propertyCoolCallFeedbacks Returns a collection of components that indicate when the system is calling for cooling.

The ClimateControlComponentCallChange event will trigger with ClimateControlComponent object.


(Inherited from Thermostat)
Public propertyCoolSetpoint Sets the cool setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyCoolSetpointFeedback Reports the active cool setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with CoolSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyCoolSetpointMinus Lowers the temperature regulating setpoint for cool-only.
(Inherited from CresnetThermostat)
Public propertyCoolSetpointPlus Raises the temperature regulating setpoint for cool-only.
(Inherited from CresnetThermostat)
Public propertyCoolStages1 Indicates how many stages of cooling there are in the system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyCoolStages2 Indicates how many stages of cooling there are in the system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyCode exampleDescription Get/Set the description of this device.
(Inherited from GenericBase)
Public propertyDispGlobalPage Indicates that the Global page (consisting of the Global Send button) has been enabled for display on the thermostat LCD. The output remains true for as long as the page is enabled.
(Inherited from CresnetThermostat)
Public propertyDispHumidityModePage Indicates that the Humidity Mode page has been enabled for display on the thermostat LCD. The output remains true for as long as the page is enabled. The Humidity Mode page allows the user to enable or disable the humidifier.
(Inherited from SingleSpeedFan)
Public propertyDispHumidityViewPage Indicates that the Humidity View page has been enabled for display on the thermostat LCD. The output remains true for as long as the page is enabled. The Humidity View Page displays the relative humidity and setpoint values.
(Inherited from SingleSpeedFan)
Public propertyDisposed Property to indicate if the device has been disposed.
(Inherited from GenericDevice)
Public propertyDispOutdoorPage Indicates that the Global page (consisting of the Global Send button) has been enabled for display on the thermostat LCD. The output remains true for as long as the page is enabled.
(Inherited from CresnetThermostat)
Public propertyDispRemoteBtnPage1 Indicates that Remote page 1 has been enabled for display. The output remains true for as long as the page is enabled. The thermostats provide two Remote pages that can be used to trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyDispRemoteBtnPage2 Indicates that Remote page 2 has been enabled for display. The output remains true for as long as the page is enabled. The thermostats provide two Remote pages that can be used to trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyDualFuelSubtype Indicates the current subtype for heating/cooling systems. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyDualSetpointsAutoMode Indicates that dual-point auto mode has been enabled. The output remains true for as long as the mode is enabled. Auto mode can be enabled or disabled from the Setup menu.
(Inherited from CresnetThermostat)
Public propertyFanAuto Sets the fan to auto mode. In Auto mode, the fan runs only when the system calls.
(Inherited from CresnetThermostat)
Public propertyFanAutoFeedback Reports if the fan is currently in auto mode.
(Inherited from CresnetThermostat)
Public propertyFanCall Indicates that the fan is running. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyFanHighCallFeedback Property to indicate that the high fan call is made. True = Fan high speed call is made; False = Fan high speed call is not made

The FanCallChange event will trigger for this property.

Public propertyFanLowCallFeedback Property to indicate that the low fan call is made. True = Fan low speed call is made; False = Fan low speed call is not made.

The FanCallChange event will trigger for this property.

Public propertyFanMediumCallFeedback Property to indicate that the medium fan call is made. True = Fan medium speed call is made; False = Fan medium speed call is not made.

The FanCallChange event will trigger for this property.

Public propertyFanOn Sets the fan to on mode. In On mode, the fan runs continually.
(Inherited from CresnetThermostat)
Public propertyFanOnFeedback Reports if the fan is currently in on mode.
(Inherited from CresnetThermostat)
Public propertyFanSpeed Property to set the current Fan speed.
Public propertyFanSpeedFeedback Property to report the currently enabled fan speed.

The BaseEvent event will trigger with FanSpeedChangedEventId for this property.

Public propertyFloorWarmSysModeHeat Turns the floor-warming system on. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyFloorWarmSysModeHeatFeedback Reports the status of the floor-warming system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyFloorWarmSysModeOff Turns the floor-warming system off. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyFloorWarmSysModeOffFeedback Reports the status of the floor-warming system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyForceAirSubtype Indicates the current subtype for heating/cooling systems. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyFrontPanelLockout Locks out the four hard pushbuttons on the thermostat for as long as the input remains true. In this mode, pressing the buttons will have no effect. Automatically disabled in case of system error or failure.
(Inherited from CresnetThermostat)
Public propertyGlobalPress Briefly pulses whenever the Send button of the Global Update page is pressed. This signal can be tied to logic in the program to trigger functions such as global updates of temperature or humidity values.
(Inherited from CresnetThermostat)
Public propertyHeatAnticipator Reports the heat anticipator values, from 1 to 6. Prevents overshooting the set temperature. A lower number signifies more frequent cycles and faster response (tighter regulation), while a higher number signifies less frequent cycles and slower response (looser regulation).
(Inherited from CresnetThermostat)
Public propertyHeatCallFeedbacks Returns a collection of components that indicate when the system is calling for heat.

The ClimateControlComponentCallChange event will trigger with ClimateControlComponent object.


(Inherited from Thermostat)
Public propertyHeatCoolType Reports the maximum slab temperature value. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyHeatPumpType Indicates the current system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyHeatSetpoint Sets the heat setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyHeatSetpointFeedback Reports the active heat setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with HeatSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyHeatSetpointMinus Lowers the temperature regulating setpoint for heat-only.
(Inherited from CresnetThermostat)
Public propertyHeatSetpointPlus Raises the temperature regulating setpoint for heat-only.
(Inherited from CresnetThermostat)
Public propertyHeatStages1 Indicates how many stages of heating there are in the system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyHeatStages2 Indicates how many stages of heating there are in the system. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyHoldOff Turns off the Hold function.
(Inherited from CresnetThermostat)
Public propertyHoldOn Turns on the Hold function.
(Inherited from CresnetThermostat)
Public propertyHPBalancePoint Reports the heat pump balance point in tenths of a degree. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyHumidifierEnable Enables the humidifier.
(Inherited from SingleSpeedFan)
Public propertyHumidifierEnableFeedback Indicates that the humidifier is enabled.
(Inherited from SingleSpeedFan)
Public propertyHumidifierOff Turns off the humidifier.
(Inherited from SingleSpeedFan)
Public propertyHumidifierOffFeedback Indicates that the humidifier is off.
(Inherited from SingleSpeedFan)
Public propertyHumidityCallFeedbacks Returns a collection of components that indicate when the system is calling for humidity.
(Inherited from SingleSpeedFan)
Public propertyHumiditySetpoint Sets the humidity regulating setpoint in whole numbers. Valid values range from 5 to 90. Out of range values are ignored.
(Inherited from SingleSpeedFan)
Public propertyHumiditySetpointFeedback Reports the humidity regulating setpoint.
(Inherited from SingleSpeedFan)
Public propertyHumiditySetpointMinus Lowers the humidity regulating setpoint. Continuing to assert the up or down inputs at the limits of the setpoint will not affect the setpoint. That is, the setpoint will hold at its maximum or minimum setting.
(Inherited from SingleSpeedFan)
Public propertyHumiditySetpointPlus Raises the humidity regulating setpoint. Continuing to assert the up or down inputs at the limits of the setpoint will not affect the setpoint. That is, the setpoint will hold at its maximum or minimum setting.
(Inherited from SingleSpeedFan)
Public propertyID Property to get the ID of the device.
(Inherited from GenericDevice)
Public propertyIndoorHumidityInput Receives the indoor relative humidity from a sensor that is not connected to the thermostat, for display on the Main page of the thermostat LCD (CHV-TSTAT only). This value is ignored if a humidity sensor (CHV-RTHS) is connected to the CHV-TSTAT.
(Inherited from SingleSpeedFan)
Public propertyInterstageDifferential Reports the interstage differential in tenths of a degree. This is the proportional temperature error to trigger the second (Auxiliary) stage. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyIsOnline Property to get the current online state of the device.
(Inherited from GenericDevice)
Public propertyLCDContrast Reports the LCD screen contrast. Values range from 1 (lightest) to 10 (darkest).
(Inherited from CresnetThermostat)
Public propertyLocalHumidity Reports the relative humidity reading of the built-in humidity sensor (CHV-THSTAT only) in whole numbers. The internal humidity sensor reading is reported regardless of the Use or Omit designation.
(Inherited from SingleSpeedFan)
Public propertyLocalHumInvalid Indicates that the corresponding when remote humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from SingleSpeedFan)
Public propertyLocalTemperatureFeedback Reports the local temperature reported by the Local sensor. Only enabled when EnableSensorOutputs is enabled. This property is supported by "HZThstat" not supported by "DinThstat".

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyLocalTemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertyMainScrnObHumidity Reports the reading that will be displayed under the current temperature on the Main page of the thermostat LCD.
(Inherited from SingleSpeedFan)
Public propertyMainScrnObNA Reports that NA will be displayed under the current temperature on the Main page of the thermostat LCD.
(Inherited from CresnetThermostat)
Public propertyMainScrnObOutdoor Reports that outdoor will be displayed under the current temperature on the Main page of the thermostat LCD.
(Inherited from CresnetThermostat)
Public propertyMainScrnObSlabTemperature Reports that slab will be displayed under the current temperature on the Main page of the thermostat LCD.
(Inherited from CresnetThermostat)
Public propertyMaxSlabTemperature Reports the maximum slab temperature value. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. Values range from 390 to 1220 (39° to 122°F); or 44 to 500 (4° to 50°C). This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyMsgField Sends text string to the Messages page of the thermostat LCD. Displayed text is limited to approximately 20 characters per line (including spaces) to a maximum of four lines. The thermostat supports word wrap and auto-hyphenation within the 20 characters/spaces per line maximum. (Carriage returns will force a line change.)
(Inherited from CresnetThermostat)
Public propertyMsgIconOn Alternately flashes the text "View Msg" with "Online/Hold, Net Fault" on the Main page of the thermostat LCD, for as long as the input remains true. This alerts the user to check for a displayed message on the Messages page of the thermostat LCD.
(Inherited from CresnetThermostat)
Public propertyMsgWaiting Indicates that text has been sent to the Messages page of the thermostat LCD, via the MsgField input. The output remains true until the user presses the Clear button on the Messages page.
(Inherited from CresnetThermostat)
Public propertyName Get the name of this device.
(Inherited from GenericBase)
Public propertyNoAutoMode Indicates that auto mode has been disabled. The output remains true for as long as auto mode is off. Auto mode can be enabled or disabled from the Setup menu.
(Inherited from CresnetThermostat)
Public propertyODHumInvalid Indicates that the corresponding when remote humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from SingleSpeedFan)
Public propertyODRem1Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyODRem1Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyODRem2Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyODRem2Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyODTemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertyOfflineHold Indicates that the thermostat has been taken offline. In this mode, the thermostat is "on hold" and data flows one way, from the thermostat to Cresnet. All Cresnet commands to the thermostat are blocked except for the Hold Off command. While the thermostat is "on hold" it buffers all setpoint and mode changes (except for up/down inputs). The setpoints and mode inputs will take effect immediately when the hold is released. Remains true for as long as the thermostat is offline.
(Inherited from CresnetThermostat)
Public propertyOmitLocalHumidity Reports the designator assigned to the local (internal) sensors.
(Inherited from SingleSpeedFan)
Public propertyOmitLocalTemperature Reports if temperature is assigned to the local (internal) sensors. The CHV-TSTAT provides one internal temperature sensor; the CHV-THSTAT provides internal sensors for temperature and humidity. Each sensor must be designated as Use or Omit. Readings from local and remote sensors that have the same designator are averaged together. Thus two temperature sensors set to Use are averaged for the air temperature control, while two humidity sensors set to Use are averaged to determine the humidity. A sensor designated as "Omit" signifies that the reading will not be included in such averaging.
(Inherited from CresnetThermostat)
Public propertyOmitRem1Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyOmitRem1Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyOmitRem2Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyOmitRem2Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyOutdoorHumidity Reports the humidity reading of any humidity sensor set to "OD" (Outdoor) in whole numbers. If more than one humidity sensor is set to OD, this is the mean outdoor humidity. Humidity sensors are manually set to Use, Omit, or Outdoor via the setup menus on the thermostat.
(Inherited from SingleSpeedFan)
Public propertyOutdoorHumidityInput Receives the outdoor relative humidity from a sensor that is not connected to the thermostat, for display on the Outdoor page of the thermostat LCD.
(Inherited from SingleSpeedFan)
Public propertyOutdoorTemperatureFeedback Sends the current outdoor temperature to the thermostat. This input should only be used for heatpump/dual fuel balance point systems, not heat/cool system types. The value should be sent in tenths of a degree (1d = 0.1 degrees) based on the current temperature scale (Fahrenheit or Celsius). For example, if the outdoor temperature is 45.3°F, the value should be 453.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyOutdoorTemperatureInput Sends the current outdoor temperature to the thermostat. This input should only be used for heatpump/dual fuel balance point systems, not heat/cool system types. The value should be sent in tenths of a degree (1d = 0.1 degrees) based on the current temperature scale (Fahrenheit or Celsius). For example, if the outdoor temperature is 45.3°F, the value should be 453d.
(Inherited from Thermostat)
Public propertyParent The parent that a given object was added to.
(Inherited from GenericBase)
Public propertyPoint5CSteps Indicates that the temperature in Celsius will be displayed in half degrees.
(Inherited from CresnetThermostat)
Public propertyRadiantSubtype Indicates the current subtype for heating/cooling systems. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertyRawRelayStateMaskFeedback Property to report the currently engaged relays as a mask.

The BaseEvent event will trigger with RawRelayStateMaskEventId for this property.

Public propertyRegHumInvalid Indicates that the corresponding when remote humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from SingleSpeedFan)
Public propertyRegisterable Property to indicate that this device can be registered.
(Inherited from GenericDevice)
Public propertyRegistered Property to get the current registration state of the device.
(Inherited from GenericDevice)
Public propertyRegistrationFailureReason Property to get the Registration Failure Reason, this will match the return value from the call to register.
(Inherited from GenericDevice)
Public propertyRegTemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertyRegulationHumidity Reports the mean (averaged) humidity reading of all internal and remote humidity sensors set to "Use", in whole numbers. Humidity sensors are manually set to Use, Omit, or Outdoor via the setup menus on the thermostat.
(Inherited from SingleSpeedFan)
Public propertyRegulationTemperatureFeedback Reports displayed temperature, which can be the Local temperature or the Remote 1 temperature, or the average of Local and Remote 1, based on the option selected in the Setup menu (Local = i; Remote 1 = r; Average = ir).

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyRem1HumInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from SingleSpeedFan)
Public propertyRem1TemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertyRem2HumInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from SingleSpeedFan)
Public propertyRem2TemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertyRemote1Humidity Reports the humidity reading of the Remote 1 humidity sensor in whole numbers. The Remote 1 humidity reading is reported regardless of the Use/Omit/OD designation.
(Inherited from SingleSpeedFan)
Public propertyRemote1TemperatureFeedback Reports the temperature reported by the Remote 1 sensor. Only enabled when EnableSensorOutputs is enabled.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyRemote2Humidity Reports the humidity reading of the Remote 2 humidity sensor in whole numbers. The Remote 2 humidity reading is reported regardless of the Use/Omit/OD designation.
(Inherited from SingleSpeedFan)
Public propertyRemote2TemperatureFeedback Reports the local temperature reported by the Remote 2 sensor. Only enabled when EnableSensorOutputs is enabled.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyRemotePageOneDownButton Indicates the state of the Down button on Remote Page one of the thermostat LCD. The output remains true for as long as the button is pressed. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC "remote" functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageOneDownButtonLabel Sends text label for display next to the Down button on Remote Page one of the thermostat LCD. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageOneUpButton Indicates the state of the Up button on Remote Page one of the thermostat LCD. The output remains true for as long as the button is pressed. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC "remote" functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageOneUpButtonLabel Sends text label for display next to the Up button on Remote Page one of the thermostat LCD. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageTwoDownButton Indicates the state of the Down button on Remote Page two of the thermostat LCD. The output remains true for as long as the button is pressed. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC "remote" functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageTwoDownButtonLabel Sends text label for display next to the Down button on Remote Page two of the thermostat LCD. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageTwoUpButton Indicates the state of the Up button on Remote Page two of the thermostat LCD. The output remains true for as long as the button is pressed. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC "remote" functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRemotePageTwoUpButtonLabel Sends text label for display next to the Up button on Remote Page two of the thermostat LCD. The thermostat LCD provides two Remote pages in which the Up and Down pushbuttons operate as remote function buttons. In this mode the buttons can trigger non-HVAC functions such as AV control, lighting, or alarm activation.
(Inherited from CresnetThermostat)
Public propertyRevSmodeDir Indicates the direction of system mode toggling in response to up/down button presses. The output becomes true when the Setup option for "Reverse System Mode Direction" is set to "Y". In this mode, the UP button moves the mode select box to the right instead of to the left.
(Inherited from CresnetThermostat)
Public propertyRunBacklight Turns on the thermostat's backlight for 8 seconds.
(Inherited from CresnetThermostat)
Public propertyRunFanHeatCalls Indicates that Run Fan in Heat Calls has been enabled. The output remains true for as long as the mode is enabled. Run Fan in Heat Calls is a device setting that activates the fan output with W1/W2 heat calls. Does not enable operation on slab systems on the slab (W1) call.
(Inherited from CresnetThermostat)
Public propertyShortCycleProtectionTimeFeedback Property to report short cycle timeout(seconds) setting.

The BaseEvent event will trigger with ShortCycleProtectionTimeEventId for this property.

Protected propertySIMPLDeviceImplementation Internal protected member used for actual device control.
(Inherited from GenericDevice)
Public propertySlab1Type Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab2Type Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab3Type Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab4AType Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab4BType Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab5AType Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlab5BType Indicates the current slab system type. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabHeatCallFeedbacks Returns a collection of components that indicate when the system is calling for slab heat. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabMinSetpointMinus Lowers the slab regulating setpoint. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabMinSetpointPlus Raises the slab regulating setpoint. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabRegulation Reports the slab temperature regulation value. Values range from 1 to 6. A lower number signifies less frequent cycles and slower response (looser regulation), while a higher number signifies more frequent cycles and faster response (tighter regulation). This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabRem1Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertySlabRem2Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertySlabSetpoint Sets the slab regulating setpoint in tenths of a degree. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. The displayed setpoint value is rounded to whole degrees Fahrenheit or Celsius, or half-degrees Celsius if that option is enabled. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabSetpointFeedback Reports the slab regulating setpoint in tenths of a degree. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySlabTemperature Reports the temperature reading of any remote sensor set to "Slab", in tenths of a degree. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. If more than one sensor is set to "Slab", this is the mean slab temperature. Sensors are set to Use, Omit, OD (Outdoor) or Slab via the setup menus on the thermostat.
(Inherited from CresnetThermostat)
Public propertySlabTemperatureInvalid Indicates that the corresponding when remote temperature/humidity sensor isn't reporting valid data. The output remains true for as long as the sensor source doesn't have valid data. This can indicate a problem with the sensor, or the sensor being absent.
(Inherited from CresnetThermostat)
Public propertySysModeAuto Selects auto mode (auto selects heat or cool).
(Inherited from CresnetThermostat)
Public propertySysModeAutoFeedback Reports if auto mode is the current system mode.
(Inherited from CresnetThermostat)
Public propertySysModeAuxHeatOnly Selects auxiliary heat-only mode for heat pump systems (no effect on a heat/cool system). This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySysModeAuxHeatOnlyFeedback Reports the current system mode. This property is not supported by ChvTstatFcu Thermostat.
(Inherited from SingleSpeedFan)
Public propertySysModeCool Selects cool-only mode.
(Inherited from CresnetThermostat)
Public propertySysModeCoolFeedback Reports if cool mode is the current system mode.
(Inherited from CresnetThermostat)
Public propertySysModeHeat Selects heat-only mode.
(Inherited from CresnetThermostat)
Public propertySysModeHeatFeedback Reports if heat mode is the current system mode.
(Inherited from CresnetThermostat)
Public propertySysModeOff Selects off mode (no HVAC operation).
(Inherited from CresnetThermostat)
Public propertySysModeOffFeedback Reports if off mode is the current system mode.
(Inherited from CresnetThermostat)
Public propertyTemperatureDegC Indicates that Celcius is the temperature scale.
(Inherited from CresnetThermostat)
Public propertyTemperatureDegF Indicates that Fahrenheit is the temperature scale.
(Inherited from CresnetThermostat)
Public propertyTemperatureDispOffset Reports the temperature offset in tenths of a degree. The offset is the number of degrees added or subtracted from the actual sensed temperature. The scale (Fahrenheit or Celsius) is based on the current setting in the unit. Values are as follows: Fahrenheit: -60 to +60 (-6˚ to +6˚F) Celsius: -30 to +30 (-3˚ to +3˚C) Half degrees Celsius mode: -35 to +35 (-3.5˚to +3.5˚C) This temperature offset changes the actual regulated temperature, not just the displayed temperature. The offset is set to "0" as shipped from the factory.
(Inherited from CresnetThermostat)
Public propertyType Property to determine to type of device this is.
(Inherited from GenericDevice)
Public propertyUnRegistrationFailureReason Property to get the Unregistration Failure Reason, this will match the return value from the call to unregister.
(Inherited from GenericDevice)
Public propertyUseLocalHumidity Reports the designator assigned to the local (internal) sensors.
(Inherited from SingleSpeedFan)
Public propertyUseLocalTemperature Reports if temperature is assigned to the local (internal) sensors. The CHV-TSTAT provides one internal temperature sensor; the CHV-THSTAT provides internal sensors for temperature and humidity. Each sensor must be designated as Use or Omit. Readings from local and remote sensors that have the same designator are averaged together. Thus two temperature sensors set to Use are averaged for the air temperature control, while two humidity sensors set to Use are averaged to determine the humidity. A sensor designated as "Omit" signifies that the reading will not be included in such averaging.
(Inherited from CresnetThermostat)
Public propertyUseRem1Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyUseRem1Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyUseRem2Humidity Reports the designator assigned to the remote sensors.
(Inherited from SingleSpeedFan)
Public propertyUseRem2Temperature Reports the designator assigned to the remote sensors.
(Inherited from CresnetThermostat)
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from GenericBase)
Public propertyWideRangeCool Indicates that wide range cool mode has been enabled. The output remains true for as long as the mode is enabled. Wide range cool extends the cool setpoint range to the full auto range of 38° to 99°F, or 3° to 37°C. This is suitable for wine cellars or other colder chilling processes.
(Inherited from CresnetThermostat)
Protected propertyXioEndpointStubSIMPLDevice The SIMPL "stub" Device that the XiO Director creates for an endpoint to send the 1C/0E to the correct place in hierarchy.
(Inherited from GenericDevice)
Top
See Also