Click or drag to resize

ChvTstatexFcu Properties

The ChvTstatexFcu type exposes the following members.

Properties
 NameDescription
Public propertyAuto1ptSetpoint Sets the auto1pt setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyAuto1ptSetpointFeedback Reports the active auto1pt setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with Auto1ptSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyAutoAsSingleSetpointFeedback Indicates that single-setpoint auto mode is enabled (the "s" option for auto mode has been selected in the Setup menu). The output remains true for as long as single-setpoint auto mode is active.
(Inherited from RFThermostat)
Public propertyAutoDeadbandFeedback Reports the auto deadband value selected via the "db" option in the Setup menu, where 1d = 0.1 degrees. In dual-setpoint auto mode, this value is the minimum separation between heat and cool setpoints, which prevents the system from toggling back and forth due to overshoot. In single-setpoint auto mode, this value sets the hysteresis used when changing from heat to cool. For example, if the setpoint is 70°F with auto deadband of 2 degrees, the temperature would have to rise to 72°F before running cool, and 68°F before running heat. HZ-THSTAT reports auto mode deadband parameter in 10ths of current unit: Fahrenheit : 20, 30, 40, 50, 60 (F). Celsius : 10, 20, 30 (C).

The BaseEvent event will trigger with AutoDeadbandFeedbackEventId.


(Inherited from Thermostat)
Public propertyAutoModeEnabledFeedback Indicates that the auto mode has been enabled. The output remains true for as long as the mode is enabled. Note that this output only indicates that the unit has been configured to support the corresponding mode; it does not indicate whether or not the unit is actively in that mode.
(Inherited from RFThermostat)
Public propertyAuxHeatAvailableFeedback Indicates that the system is capable of running an auxiliary heat system (heat pump systems only). The output remains true for as long as the system supports auxiliary heat.
(Inherited from RFThermostat)
Public propertyBatteryState Returns the current battery state.
(Inherited from RFThermostat)
Public propertyConnectedIpList A property containing the list of the ConnectedIpInformation objects which contain information about the devices that are connected to this IP ID. This property is only valid for an ethernet device. If this is not an ethernet device, then this property will return null. If this is an ethernet device, the list will be non-null. It will be empty if no devices are connected. The order of items in this list is not guaranteed.
(Inherited from GenericDevice)
Public propertyCoolCallFeedbacks Returns a collection of components that indicate when the system is calling for cooling.

The ClimateControlComponentCallChange event will trigger with ClimateControlComponent object.


(Inherited from Thermostat)
Public propertyCoolModeEnabledFeedback Indicates that the cool mode has been enabled. The output remains true for as long as the mode is enabled. Note that this output only indicates that the unit has been configured to support the corresponding mode; it does not indicate whether or not the unit is actively in that mode.
(Inherited from RFThermostat)
Public propertyCoolSetpoint Sets the cool setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyCoolSetpointFeedback Reports the active cool setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with CoolSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyCode exampleDescription Get/Set the description of this device.
(Inherited from GenericBase)
Public propertyDisableBacklight Disables the backlight from turning on under any condition, for as long as the input is true. This can be used to extend battery life.
(Inherited from RFThermostat)
Public propertyDisplayUnit Reports the current temperature format.
(Inherited from RFThermostat)
Public propertyDisplayUnitFeedback Reports the current temperature format.
(Inherited from RFThermostat)
Public propertyDisposed Property to indicate if the device has been disposed.
(Inherited from GenericDevice)
Public propertyEnableSensorOutputs Enables temperature reporting on Slot 01 for the Local Remote 1 and Remote 2 sensors.
(Inherited from RFThermostat)
Public propertyFanCallHighFeedback Indicates that the 3-speed fan is running at high speed. The output remains true for as long as the fan is running at high speed.
Public propertyFanCallLowFeedback Indicates that the 3-speed fan is running at low speed. The output remains true for as long as the fan is running at low speed.
Public propertyFanCallMedFeedback Indicates that the 3-speed fan is running at medium speed. The output remains true for as long as the fan is running at medium speed.
Public propertyFanMode Sets the fan mode.
(Inherited from RFThermostat)
Public propertyFanModeFeedback Reports the current fan mode.
(Inherited from RFThermostat)
Public propertyFanSpeedLowEnabledFeedback Indicates that the low fan speed has been enabled (via the Setup screens). The output remains true for as long as the fan speed is enabled. Note that this output only indicates that the unit has been configured to support the corresponding fan speed; it does not indicate whether or not the unit is actively in that mode.
Public propertyFanSpeedMediumEnabledFeedback Indicates that the medium fan speed has been enabled (via the Setup screens). The output remains true for as long as the fan speed is enabled. Note that this output only indicates that the unit has been configured to support the corresponding fan speed; it does not indicate whether or not the unit is actively in that mode.
Public propertyHeatCallFeedbacks Returns a collection of components that indicate when the system is calling for heat.

The ClimateControlComponentCallChange event will trigger with ClimateControlComponent object.


(Inherited from Thermostat)
Public propertyHeatModeEnabledFeedback Indicates that the heat mode has been enabled. The output remains true for as long as the mode is enabled. Note that this output only indicates that the unit has been configured to support the corresponding mode; it does not indicate whether or not the unit is actively in that mode.
(Inherited from RFThermostat)
Public propertyHeatSetpoint Sets the heat setpoint, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius). The displayed value is rounded to whole or half degrees based on the setting.
(Inherited from Thermostat)
Public propertyHeatSetpointFeedback Reports the active heat setpoint value. This output should be connected to the corresponding setpoint input; otherwise the output will not report the setpoint value.

The BaseEvent event will trigger with HeatSetpointFeedbackEventId.


(Inherited from Thermostat)
Public propertyHoldMode Sets the hold mode as follows: 1d = Hold mode ON 2d = Hold mode OFF (Run mode ON) When hold mode is active, the setpoint can be manually adjusted, either locally or via the Simpl#Pro program. All scheduled setpoints are ignored until the unit is taken out of hold mode. When the hold state changes from Hold (1d) to Run (2d), the unit will recall the last scheduled setpoint.
(Inherited from RFThermostat)
Public propertyHoldModeFeedback Reports the current hold mode.
(Inherited from RFThermostat)
Public propertyID Property to get the ID of the device.
(Inherited from GenericDevice)
Public propertyIsOnline Property to get the current online state of the device.
(Inherited from GenericDevice)
Public propertyLocalTemperatureFeedback Reports the local temperature reported by the Local sensor. Only enabled when EnableSensorOutputs is enabled. This property is supported by "HZThstat" not supported by "DinThstat".

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyMaxAuto1ptSetpointFeedback Reports the maximum allowable single-point auto setpoint that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyMaxCoolSetpointFeedback Reports the maximum allowable cool that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyMaxHeatSetpointFeedback Reports the maximum allowable heat that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyMinAuto1ptSetpointFeedback Reports the minimum allowable single-point auto setpoint that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyMinCoolSetpointFeedback Reports the minimum allowable cool that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyMinHeatSetpointFeedback Reports the minimum allowable heat that the system supports, where 1d = 0.1 degrees. The value is based on the current temperature scale (Fahrenheit or Celsius), as reported by DisplayUnitFeedback.
(Inherited from RFThermostat)
Public propertyName Get the name of this device.
(Inherited from GenericBase)
Public propertyOutdoorTemperatureFeedback Sends the current outdoor temperature to the thermostat. This input should only be used for heatpump/dual fuel balance point systems, not heat/cool system types. The value should be sent in tenths of a degree (1d = 0.1 degrees) based on the current temperature scale (Fahrenheit or Celsius). For example, if the outdoor temperature is 45.3°F, the value should be 453.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyOutdoorTemperatureInput Sends the current outdoor temperature to the thermostat. This input should only be used for heatpump/dual fuel balance point systems, not heat/cool system types. The value should be sent in tenths of a degree (1d = 0.1 degrees) based on the current temperature scale (Fahrenheit or Celsius). For example, if the outdoor temperature is 45.3°F, the value should be 453d.
(Inherited from Thermostat)
Public propertyParent The parent that a given object was added to.
(Inherited from GenericBase)
Public propertyRegisterable Property to indicate that this device can be registered.
(Inherited from GenericDevice)
Public propertyRegistered Property to get the current registration state of the device.
(Inherited from GenericDevice)
Public propertyRegistrationFailureReason Property to get the Registration Failure Reason, this will match the return value from the call to register.
(Inherited from GenericDevice)
Public propertyRegulationTemperatureFeedback Reports displayed temperature, which can be the Local temperature or the Remote 1 temperature, or the average of Local and Remote 1, based on the option selected in the Setup menu (Local = i; Remote 1 = r; Average = ir).

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyRemote1TemperatureFeedback Reports the temperature reported by the Remote 1 sensor. Only enabled when EnableSensorOutputs is enabled.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertyRemote2TemperatureFeedback Reports the local temperature reported by the Remote 2 sensor. Only enabled when EnableSensorOutputs is enabled.

The TemperatureChange event will trigger with temperatureType and newTemperature.


(Inherited from Thermostat)
Public propertySensorConfigurationFeedback 16-bit analog value that reports sensor configuration information, as follows: bits 15 and 14: 2-bit version code, currently 00 bits 13 and 12: Reserved bit 11: RS2 temperature data valid (1) or invalid (0) bit 10: RS1 temperature data valid (1) or invalid (0) bit 9: Local temperature valid (1) or invalid (0) bit 8: RS2 sensor type digital (0) or analog/NTC (1) bit 7: RS1 sensor type digital (0) or analog/NTC (1) bit 6: Local sensor type digital (0) or analog/NTC (1) bits 5 and 4: RS2 usage code (see below) bits 3 and 2: RS1 usage code bits 1 and 0: Local usage code Usage code 00: Not used/averaged 01: For regulation temperature 10: For outdoor temperature 11: For specific sensing (i.e., FCU changeover)
(Inherited from RFThermostat)
Public propertySetpointsSchedule Returns a ScheduledSetpoints object that has all of the thermostats scheduled setpoints cues.
(Inherited from RFThermostat)
Protected propertySIMPLDeviceImplementation Internal protected member used for actual device control.
(Inherited from GenericDevice)
Public propertySystemConfigurationFeedback For internal Crestron use only.
(Inherited from RFThermostat)
Public propertySystemMode Sets the system mode, as follows: When the system mode changes the unit will recall the last scheduled setpoint for that new mode. This output should be connected to the HoldMode input; otherwise the output it will not track the value of HoldMode.
(Inherited from RFThermostat)
Public propertySystemModeFeedback Reports the current system mode.
(Inherited from RFThermostat)
Public propertyType Property to determine to type of device this is.
(Inherited from GenericDevice)
Public propertyUnRegistrationFailureReason Property to get the Unregistration Failure Reason, this will match the return value from the call to unregister.
(Inherited from GenericDevice)
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from GenericBase)
Protected propertyXioEndpointStubSIMPLDevice The SIMPL "stub" Device that the XiO Director creates for an endpoint to send the 1C/0E to the correct place in hierarchy.
(Inherited from GenericDevice)
Top
See Also