Click or drag to resize

BACnetRemoteBinaryOutputObject Properties

The BACnetRemoteBinaryOutputObject type exposes the following members.

Properties
 NameDescription
Public propertyCovLifetime Parameter to specify the default Change of Value (COV) notification lifetime in minutes. Default value is 30 minutes.
(Inherited from BACnetRemoteCommonObject)
Public propertyDisposed Property to indicate if the Device has been disposed.
(Inherited from BACnetObject)
Public propertyEventStateFeedback Property to indicate the event state associated with the object.

This property will trigger BACnetObjectChange event with EventStateFeedbackEventId.


(Inherited from BACnetRemoteCommonObject)
Public propertyId A 22-bit decimal number that serves as an unique address of the object within the BACnet device. Valid range from 0 to 4194302.
(Inherited from BACnetObject)
Public propertyOutOfServiceFeedback Property to report whether the BACnet object is functioning as expected or not. true means the object is out of service. false means it is in service.

This property will trigger BACnetObjectChange event with OutOfServiceChangedEventId.


(Inherited from BACnetRemoteCommonObject)
Public propertyParent The parent that a given object was added to.
(Inherited from BACnetObject)
Public propertyPresentValueClearedFeedback Changes from false to true and again to false to indicate PresentValueFeedback is cleared (set to false).

This property will trigger BACnetObjectChange event with PresentValueClearedEventId.


(Inherited from BACnetRemoteBinaryInputObject)
Public propertyPresentValueFeedback Property to report the Present Value of the object.

This property will trigger BACnetObjectChange event with PresentValueFeedbackEventId.


(Inherited from BACnetRemoteBinaryInputObject)
Public propertyPresentValueSetFeedback Changes from false to true and again to false to indicate PresentValueFeedback is set (set to true).

This property will trigger BACnetObjectChange event with PresentValueSetEventId.


(Inherited from BACnetRemoteBinaryInputObject)
Public propertyPriority Parameter to specify the BACnet priority level at which the object will communicate. There are 16 levels of priority, where level 1 denotes the highest priority and level 16 - the lowest.
(Inherited from BACnetRemoteCommonObject)
Public propertyPriorityForPresentValueFeedback Indicates the write priority of the present value recently received from the remote device. This property value is updated either by calling PollForValue method or by sending an RPM request for this object internally from the BACnet Stack to the Host Device. This property is not supported on firmware with version less than "4.0003.00005" on VC4 platforms. This property is not supported on firmware with version less than "2.8004.00001" on 4-Series platform. This property is not supported on 3-Series platforms.

This property will trigger BACnetObjectChange event with PriorityForPresentValueFeedbackEventId.


(Inherited from BACnetRemoteBinaryValueOutputCommonObject)
Public propertyScanRate Parameter to specify the default time interval (in seconds) for polling the device properties. This parameter will be ignored if the user chooses to set the polling interval by using the VariableScanRate. Default value = 30s.
(Inherited from BACnetRemoteCommonObject)
Public propertyStatusFlagsFeedback Property to report the state of the four Boolean flags that indicate the general "health" of the remote object.

This property will trigger BACnetObjectChange event with StatusFlagsFeedbackEventId.


(Inherited from BACnetRemoteCommonObject)
Public propertySubscribeCov Parameter that indicates if the BACnet device subscribes to Change of Value (COV) notification. Valid values as follows: true = subscribes to COV notification; false = Does not subscribe COV notification Default-value = true (subscribes to COV notification)
(Inherited from BACnetRemoteCommonObject)
Public propertyType Type of the BACnet object.
(Inherited from BACnetObject)
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from BACnetObject)
Public propertyVariableScanRate When non-zero, will cause the BACnet stack to poll for the value periodically. When set to zero will poll for value at the specified interval set by the ScanRate parameter.
(Inherited from BACnetRemoteCommonObject)
Public propertyWritePriority Write priority of this object.
(Inherited from BACnetRemoteBinaryValueOutputCommonObject)
Top
See Also