Click or drag to resize

DmMd4kOutputEqualizer Class

Equalizer control for the DmMd4k audio output stream.
Inheritance Hierarchy

Namespace: SimplSharpProDM
Assembly: SimplSharpPro (in SimplSharpPro.dll) Version: 2.21.121
Syntax
C#
public class DmMd4kOutputEqualizer : Dmps3AudioOutputEqualizer

The DmMd4kOutputEqualizer type exposes the following members.

Properties
 NameDescription
Public propertyBass Adjusts the bass settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyBassDown Decrease the bass level of the specified output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyBassFeedback Returns the current bass settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.

The DMOutputChange event will trigger with BassFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyBassUp Increase the bass level of the specified output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyEqualizerType The type of equalizer available.
(Inherited from OutputEqualizerBase)
Public propertyGeqGain125Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 125Hz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain125HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 125Hz frequency band.

The DMOutputChange event will trigger with GeqGain125HzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain16KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 16KHz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain16KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 16KHz frequency band.

The DMOutputChange event will trigger with GeqGain16KHzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain1KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 1KHz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain1KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 1KHz frequency band.

The DMOutputChange event will trigger with GeqGain1KHzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain250Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 250Hz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain250HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 250Hz frequency band.

The DMOutputChange event will trigger with GeqGain250HzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain2KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 2KHz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain2KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 2KHz frequency band.

The DMOutputChange event will trigger with GeqGain2KHzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain315Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 31.5Hz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain315HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 31.5Hz frequency band.

The DMOutputChange event will trigger with GeqGain315HzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain4KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 4KHz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain4KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 4KHz frequency band.

The DMOutputChange event will trigger with GeqGain4KHzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain500Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 500Hz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain500HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 500Hz frequency band.

The DMOutputChange event will trigger with GeqGain500HzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain63Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 63Hz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain63HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 63Hz frequency band.

The DMOutputChange event will trigger with GeqGain63HzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain8KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 8KHz frequency band.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyGeqGain8KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 8KHz frequency band.

The DMOutputChange event will trigger with GeqGain8KHzFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterAttack Sets the attack time, which is the time in milliseconds that it takes the limiter to start clipping the signal level after the threshold has been exceeded. Valid values range from 1 (0.1ms) to 3000 (300ms).
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterAttackFeedback Retrieves the attack time, which is the time in milliseconds that it takes the limiter to start clipping the signal level after the threshold has been exceeded. Valid values range from 1 (0.1ms) to 3000 (300ms).

The DMOutputChange event will trigger with LimiterAttackFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterDisableFeedback Indicates that limiting is disabled.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterEnableFeedback Indicates that limiting is enabled.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterHold Not supported on the DMPS3's Audio Output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterHoldFeedback Not supported on the DMPS3's Audio Output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterRatio Sets the limiter ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. Valid values range from 1 (1:1) to 10 (10:1).
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterRatioFeedback Retrieves the limiter ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. Valid values range from 1 (1:1) to 10 (10:1).

The DMOutputChange event will trigger with LimiterRatioFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterRelease Sets the release time, which is the time over which the limiter will stop clipping after the signal crosses under the threshold. Valid values range from 1 (1ms) to 1000 (1000ms)
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterReleaseFeedback Retrieves the release time, which is the time over which the limiter will stop clipping after the signal crosses under the threshold. Valid values range from 1 (1ms) to 1000 (1000ms)

The DMOutputChange event will trigger with LimiterReleaseFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterSoftKneeOffFeedback Indicates that soft knee limiting is disabled. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterSoftKneeOnFeedback Indicates that soft knee limiting is enabled. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterThreshold Sets the limiting threshold. Valid values range from -800 (-80dB) to 0 (0dB) Once the signal exceeds the threshold, the limiter will clip the level to the threshold value. In this way, the output signal level will never exceed the threshold.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyLimiterThresholdFeedback Retrieves the limiting threshold. Valid values range from -800 (-80dB) to 0 (0dB) Once the signal exceeds the threshold, the limiter will clip the level to the threshold value. In this way, the output signal level will never exceed the threshold.

The DMOutputChange event will trigger with LimiterThresholdFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyParent The parent that a given object was added to.
(Inherited from OutputEqualizerBase)
Public propertyTreble Adjusts the treble settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyTrebleDown Decrease the treble level of the specified output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyTrebleFeedback Returns the current treble settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.

The DMOutputChange event will trigger with TrebleFeedbackEventId.


(Inherited from Dmps3AudioOutputEqualizer)
Public propertyTrebleUp Increase the treble level of the specified output.
(Inherited from Dmps3AudioOutputEqualizer)
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from OutputEqualizerBase)
Top
Methods
 NameDescription
Public methodBassFlat Sets the Bass to 0dB.
(Inherited from Dmps3AudioOutputEqualizer)
Public methodEqualsDetermines whether the specified object is equal to the current object.
(Inherited from Object)
Protected methodFinalizeAllows an object to try to free resources and perform other cleanup operations before it is reclaimed by garbage collection.
(Inherited from Object)
Public methodGetHashCodeServes as the default hash function.
(Inherited from Object)
Public methodGetTypeGets the Type of the current instance.
(Inherited from Object)
Public methodLimiterDisable Disable Limiting.
(Inherited from Dmps3AudioOutputEqualizer)
Public methodLimiterEnable Enable limiting.
(Inherited from Dmps3AudioOutputEqualizer)
Public methodLimiterSoftKneeOff Disables soft knee limiting. The input only has an effect if LimiterEnable() has been called. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
(Inherited from Dmps3AudioOutputEqualizer)
Public methodLimiterSoftKneeOn Enables soft knee limiting. The input only has an effect if LimiterEnable() has been called. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
(Inherited from Dmps3AudioOutputEqualizer)
Protected methodMemberwiseCloneCreates a shallow copy of the current Object.
(Inherited from Object)
Public methodToString String representation of this DM output equalizer.
(Inherited from OutputEqualizerBase)
Public methodTrebleFlat Sets the Treble to 0dB.
(Inherited from Dmps3AudioOutputEqualizer)
Top

Version Information

.NET

Supported in: 6.0

.NET Compact Framework

Supported in: 3.5
See Also