Click or drag to resize

Dmps3Microphone Properties

The Dmps3Microphone type exposes the following members.

Properties
 NameDescription
Public propertyClipFeedBack Indicates that the mic signal level has exceeded 50% of the maximum level supported by the hardware, or 2dB below the input clip level. This signifies a mic level that is too hot.
(Inherited from DmMdMicrophone)
Public propertyCompressorAttack Sets the attack time, which is the time in milliseconds that it takes the compressor to start compressing after the threshold has been reached. Valid values range from 1 (0.1ms) to 250 (25ms), where 1 = 0.1ms.
(Inherited from DmMdMicrophone)
Public propertyCompressorAttackFeedBack Reports the attack time for compression.
(Inherited from DmMdMicrophone)
Public propertyCompressorDisableFeedBack Indicates that compression is disabled.
(Inherited from DmMdMicrophone)
Public propertyCompressorEnableFeedBack Indicates that compression is enabled.
(Inherited from DmMdMicrophone)
Public propertyCompressorHold Sets the compression hold, the time (in milliseconds), over which the compression will start after the signal crosses under the threshold. Valid values range from 1 to 200, where 1 = 1 ms.
(Inherited from DmMdMicrophone)
Public propertyCompressorHoldFeedBack Reports the compression hold.
(Inherited from DmMdMicrophone)
Public propertyCompressorRatio Sets the compression ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. For example, with a 2:1 ratio, for every 2 decibels the input signal increases, the output is allowed to increase only by 1 decibel. Valid values range from 1 (1:1) to 10 (10:1).
(Inherited from DmMdMicrophone)
Public propertyCompressorRatioFeedBack Reports the compression ratio.
(Inherited from DmMdMicrophone)
Public propertyCompressorRelease Sets the release time, which is the time over which the compressor will stop compressing after the signal crosses under the threshold, where 1 = 1ms. Valid values range from 1 (1ms) to 1000 (1000ms).
(Inherited from DmMdMicrophone)
Public propertyCompressorReleaseFeedBack Reports the release time for compression.
(Inherited from DmMdMicrophone)
Public propertyCompressorSoftKneeOffFeedBack Indicates that soft knee compression is disabled.
(Inherited from DmMdMicrophone)
Public propertyCompressorSoftKneeOnFeedBack Indicates that soft knee compression is enabled.
(Inherited from DmMdMicrophone)
Public propertyCompressorThreshold Sets the threshold for compression (gain reduction). Valid values range from -800 (-80dB) to 0 (0dB), where 1 = 0.1dB. Once the microphone signal exceeds the threshold, its gain is reduced by the specified compression ratio.
(Inherited from DmMdMicrophone)
Public propertyCompressorThresholdFeedBack Reports the compression threshold.
(Inherited from DmMdMicrophone)
Public propertyCompressorThresholdReachedFeedBack Indicates that the compression threshold has been reached.
(Inherited from DmMdMicrophone)
Public propertyDelay Sets the delay for the mic. Valid values range from 0 (0ms) to 850 (85ms), where 1 = 0.1ms.
Public propertyDelayFeedBack Indicates the audio delay.
Public propertyEqHighBandFrequency Specifies the frequency for the corresponding High Band. Valid frequency ranges are as follows: 3200 (3.2kHz) to 12800 (12.8kHz)
(Inherited from DmMdMicrophone)
Public propertyEqHighBandFrequencyFeedBack Reports the current high band frequency.
(Inherited from DmMdMicrophone)
Public propertyEqHighBandGain Specifies the gain for the High Band Valid values are -120 to 120.
(Inherited from DmMdMicrophone)
Public propertyEqHighBandGainFeedBack Reports the current high band gain.
(Inherited from DmMdMicrophone)
Public propertyEqHighMidBandFrequency Specifies the frequency for the corresponding High-Mid Band. Valid frequency ranges are as follows: 800 (800Hz) to 3200 (3.2kHz)
(Inherited from DmMdMicrophone)
Public propertyEqHighMidBandFrequencyFeedBack Reports the current high-mid band frequency.
(Inherited from DmMdMicrophone)
Public propertyEqHighMidBandGain Specifies the gain for the High-Mid Band Valid values are -120 to 120.
(Inherited from DmMdMicrophone)
Public propertyEqHighMidBandGainFeedBack Reports the current high-mid band gain.
(Inherited from DmMdMicrophone)
Public propertyEqLowBandFrequency Specifies the frequency for the Low Band. Valid frequency ranges are as follows: 50 (50Hz) to 200 (200Hz)
(Inherited from DmMdMicrophone)
Public propertyEqLowBandFrequencyFeedBack Reports the current low band frequency.
(Inherited from DmMdMicrophone)
Public propertyEqLowBandGain Specifies the gain for the Low Band Valid values are -120 to 120.
(Inherited from DmMdMicrophone)
Public propertyEqLowBandGainFeedBack Reports the current low band gain.
(Inherited from DmMdMicrophone)
Public propertyEqLowMidBandFrequency Specifies the frequency for the Low-Mid Band. Valid frequency ranges are as follows: 200 (200Hz) to 800 (800HZ)
(Inherited from DmMdMicrophone)
Public propertyEqLowMidBandFrequencyFeedBack Reports the current low-mid band frequency.
(Inherited from DmMdMicrophone)
Public propertyEqLowMidBandGain Specifies the gain for the Low-Mid Band Valid values are -120 to 120.
(Inherited from DmMdMicrophone)
Public propertyEqLowMidBandGainFeedBack Reports the current low-mid band gain.
(Inherited from DmMdMicrophone)
Public propertyGain Sets the source gain compensation. Valid analog values range from 0 (0dB) to 600 (60dB).
(Inherited from MicrophoneBase)
Public propertyGainFeedBack GainFeedBack : TODO Insert Comment Here.
(Inherited from MicrophoneBase)
Public propertyGateAttack Sets the time, in milliseconds, that it takes for the noise gate to fully open after the signal exceeds the GatingThreshold. This prevents short spikes in the input signal level, such as coughing, from opening the gate. Valid values range from 1 (1ms) to 250 (250ms).
(Inherited from DmMdMicrophone)
Public propertyGateAttackFeedBack Reports the gating attack.
(Inherited from DmMdMicrophone)
Public propertyGateDecayObsolete.
Sets the time, in milliseconds, over which the noise gate will close. This prevents the sound from stopping too abruptly—for example, during brief pauses in speech. Valid values range from 0 (0ms) to 5000 (5000ms, or 5s), with 1000 to 3000 (1s to 3s) being the most usable range.
(Inherited from DmMdMicrophone)
Public propertyGateDecayFeedBackObsolete.
Reports the gating decay.
(Inherited from DmMdMicrophone)
Public propertyGateDepth Sets the decibel level to go to when the gate is closed (1 = 0.1dB). Valid values range from -800 (-80dB, full mute) to 0 (0dB, minimum noise attenuation). Setting the depth above a full mute can help eliminate a swooping sound that can occur when the gate closes and opens.
(Inherited from DmMdMicrophone)
Public propertyGateDepthFeedBack Reports the gating depth.
(Inherited from DmMdMicrophone)
Public propertyGateDisableFeedBack Indicates that noise gating has been disabled.
(Inherited from DmMdMicrophone)
Public propertyGateEnableFeedBack Indicates that noise gating has been enabled.
(Inherited from DmMdMicrophone)
Public propertyGateHold Sets the gate hold time in milliseconds. The gate hold time over which the gate will close. Valid analog values range from 1 (1 ms) to 200 (200 ms).
(Inherited from DmMdMicrophone)
Public propertyGateHoldFeedBack Reports the current hold time in milliseconds.
(Inherited from DmMdMicrophone)
Public propertyGateLevelObsolete.
Sets the threshold for gating. The noise gate is enabled for as long as the gate is enabled. Valid values range from -800 (-80dB, full mute) to 0 (0dB). Once the microphone audio rises above the set GateLevel the gate opens, allowing the signal to pass through.
(Inherited from DmMdMicrophone)
Public propertyGateLevelFeedBackObsolete.
Indicates the gate level for the Mic/Line input.
(Inherited from DmMdMicrophone)
Public propertyGateRelease Sets the time, in milliseconds, over which the noise gate will close. This prevents the sound from stopping too abruptly—for example, during brief pauses in speech. Valid values range from 0 (0ms) to 5000 (5000ms, or 5s), with 1000 to 3000 (1s to 3s) being the most usable range.
(Inherited from DmMdMicrophone)
Public propertyGateReleaseFeedBack Reports the gating release/decay.
(Inherited from DmMdMicrophone)
Public propertyGateThreshold Sets the threshold for gating. The noise gate is enabled for as long as the gate is enabled. Valid values range from -800 (-80dB, full mute) to 0 (0dB). Once the microphone audio rises above the set GateLevel the gate opens, allowing the signal to pass through.
(Inherited from DmMdMicrophone)
Public propertyGateThresholdFeedBack Indicates the gate level for the Mic/Line input.
(Inherited from DmMdMicrophone)
Public propertyGatingFeedBack If true, Indicates if the noise gate is enabled.
(Inherited from DmMdMicrophone)
Public propertyHighPassFilterDisableFeedBack Indicates that the high pass filter has been disabled.
(Inherited from DmMdMicrophone)
Public propertyHighPassFilterEnableFeedBack Indicates that the high pass filter has been enabled.
(Inherited from DmMdMicrophone)
Public propertyID ID of this microphone.
(Inherited from MicrophoneBase)
Public propertyMicrophoneType The type of microphone available. See the IMicrophone interface for further details.
(Inherited from MicrophoneBase)
Public propertyMuteOffFeedBack Retrieve the mute off state for the specified microphone.
(Inherited from MicrophoneBase)
Public propertyMuteOnFeedBack Retrieve the mute on state for the specified microphone.
(Inherited from MicrophoneBase)
Public propertyName Get or Set the name of this microphone. This will modify the return value of the ToString method.
(Inherited from MicrophoneBase)
Public propertyNominalFeedBack Indicates that the mic signal level has exceeded the nominal level. The nominal indication is reported when the incoming mic signal is between -10dBFS and -30dBFS.
(Inherited from DmMdMicrophone)
Public propertyOwner Switcher that owns this Microphone
(Inherited from MicrophoneBase)
Public propertyPhantomPowerOffFeedBack Indicates that phantom power has been disabled.
(Inherited from DmMdMicrophone)
Public propertyPhantomPowerOnFeedBack Indicates that phantom power has been enabled.
(Inherited from DmMdMicrophone)
Public propertyVuFeedBack Reports the VU meter feedback value (volume of the audio source), when VU feedback is enabled. Reported values will range from 0 to 8.
(Inherited from DmMdMicrophone)
Top
See Also