Dm |
The DmMdMicrophone type exposes the following members.
| Name | Description | |
|---|---|---|
| ClipFeedBack | Indicates that the mic signal level has exceeded 50% of the maximum level supported by the hardware, or 2dB below the input clip level. This signifies a mic level that is too hot. | |
| CompressorAttack | Sets the attack time, which is the time in milliseconds that it takes the compressor to start compressing after the threshold has been reached. Valid values range from 1 (0.1ms) to 250 (25ms), where 1 = 0.1ms. | |
| CompressorAttackFeedBack | Reports the attack time for compression. | |
| CompressorDisableFeedBack | Indicates that compression is disabled. | |
| CompressorEnableFeedBack | Indicates that compression is enabled. | |
| CompressorHold | Sets the compression hold, the time (in milliseconds), over which the compression will start after the signal crosses under the threshold. Valid values range from 1 to 200, where 1 = 1 ms. | |
| CompressorHoldFeedBack | Reports the compression hold. | |
| CompressorRatio | Sets the compression ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. For example, with a 2:1 ratio, for every 2 decibels the input signal increases, the output is allowed to increase only by 1 decibel. Valid values range from 1 (1:1) to 10 (10:1). | |
| CompressorRatioFeedBack | Reports the compression ratio. | |
| CompressorRelease | Sets the release time, which is the time over which the compressor will stop compressing after the signal crosses under the threshold, where 1 = 1ms. Valid values range from 1 (1ms) to 1000 (1000ms). | |
| CompressorReleaseFeedBack | Reports the release time for compression. | |
| CompressorSoftKneeOffFeedBack | Indicates that soft knee compression is disabled. | |
| CompressorSoftKneeOnFeedBack | Indicates that soft knee compression is enabled. | |
| CompressorThreshold | Sets the threshold for compression (gain reduction). Valid values range from -800 (-80dB) to 0 (0dB), where 1 = 0.1dB. Once the microphone signal exceeds the threshold, its gain is reduced by the specified compression ratio. | |
| CompressorThresholdFeedBack | Reports the compression threshold. | |
| CompressorThresholdReachedFeedBack | Indicates that the compression threshold has been reached. | |
| EqHighBandFrequency | Specifies the frequency for the corresponding High Band. Valid frequency ranges are as follows: 3200 (3.2kHz) to 12800 (12.8kHz) | |
| EqHighBandFrequencyFeedBack | Reports the current high band frequency. | |
| EqHighBandGain | Specifies the gain for the High Band Valid values are -120 to 120. | |
| EqHighBandGainFeedBack | Reports the current high band gain. | |
| EqHighMidBandFrequency | Specifies the frequency for the corresponding High-Mid Band. Valid frequency ranges are as follows: 800 (800Hz) to 3200 (3.2kHz) | |
| EqHighMidBandFrequencyFeedBack | Reports the current high-mid band frequency. | |
| EqHighMidBandGain | Specifies the gain for the High-Mid Band Valid values are -120 to 120. | |
| EqHighMidBandGainFeedBack | Reports the current high-mid band gain. | |
| EqLowBandFrequency | Specifies the frequency for the Low Band. Valid frequency ranges are as follows: 50 (50Hz) to 200 (200Hz) | |
| EqLowBandFrequencyFeedBack | Reports the current low band frequency. | |
| EqLowBandGain | Specifies the gain for the Low Band Valid values are -120 to 120. | |
| EqLowBandGainFeedBack | Reports the current low band gain. | |
| EqLowMidBandFrequency | Specifies the frequency for the Low-Mid Band. Valid frequency ranges are as follows: 200 (200Hz) to 800 (800HZ) | |
| EqLowMidBandFrequencyFeedBack | Reports the current low-mid band frequency. | |
| EqLowMidBandGain | Specifies the gain for the Low-Mid Band Valid values are -120 to 120. | |
| EqLowMidBandGainFeedBack | Reports the current low-mid band gain. | |
| Gain |
Sets the source gain compensation.
Valid analog values range from 0 (0dB) to 600 (60dB).
(Inherited from MicrophoneBase) | |
| GainFeedBack |
GainFeedBack : TODO Insert Comment Here.
(Inherited from MicrophoneBase) | |
| GateAttack | Sets the time, in milliseconds, that it takes for the noise gate to fully open after the signal exceeds the GatingThreshold. This prevents short spikes in the input signal level, such as coughing, from opening the gate. Valid values range from 1 (1ms) to 250 (250ms). | |
| GateAttackFeedBack | Reports the gating attack. | |
| GateDecay | Obsolete. Sets the time, in milliseconds, over which the noise gate will close. This prevents the sound from stopping too abruptly—for example, during brief pauses in speech. Valid values range from 0 (0ms) to 5000 (5000ms, or 5s), with 1000 to 3000 (1s to 3s) being the most usable range. | |
| GateDecayFeedBack | Obsolete. Reports the gating decay. | |
| GateDepth | Sets the decibel level to go to when the gate is closed (1 = 0.1dB). Valid values range from -800 (-80dB, full mute) to 0 (0dB, minimum noise attenuation). Setting the depth above a full mute can help eliminate a swooping sound that can occur when the gate closes and opens. | |
| GateDepthFeedBack | Reports the gating depth. | |
| GateDisableFeedBack | Indicates that noise gating has been disabled. | |
| GateEnableFeedBack | Indicates that noise gating has been enabled. | |
| GateHold | Sets the gate hold time in milliseconds. The gate hold time over which the gate will close. Valid analog values range from 1 (1 ms) to 200 (200 ms). | |
| GateHoldFeedBack | Reports the current hold time in milliseconds. | |
| GateLevel | Obsolete. Sets the threshold for gating. The noise gate is enabled for as long as the gate is enabled. Valid values range from -800 (-80dB, full mute) to 0 (0dB). Once the microphone audio rises above the set GateLevel the gate opens, allowing the signal to pass through. | |
| GateLevelFeedBack | Obsolete. Indicates the gate level for the Mic/Line input. | |
| GateRelease | Sets the time, in milliseconds, over which the noise gate will close. This prevents the sound from stopping too abruptly—for example, during brief pauses in speech. Valid values range from 0 (0ms) to 5000 (5000ms, or 5s), with 1000 to 3000 (1s to 3s) being the most usable range. | |
| GateReleaseFeedBack | Reports the gating release/decay. | |
| GateThreshold | Sets the threshold for gating. The noise gate is enabled for as long as the gate is enabled. Valid values range from -800 (-80dB, full mute) to 0 (0dB). Once the microphone audio rises above the set GateLevel the gate opens, allowing the signal to pass through. | |
| GateThresholdFeedBack | Indicates the gate level for the Mic/Line input. | |
| GatingFeedBack | If true, Indicates if the noise gate is enabled. | |
| HighPassFilterDisableFeedBack | Indicates that the high pass filter has been disabled. | |
| HighPassFilterEnableFeedBack | Indicates that the high pass filter has been enabled. | |
| ID |
ID of this microphone.
(Inherited from MicrophoneBase) | |
| MicrophoneType |
The type of microphone available. See the IMicrophone interface for further details.
(Inherited from MicrophoneBase) | |
| MuteOffFeedBack |
Retrieve the mute off state for the specified microphone.
(Inherited from MicrophoneBase) | |
| MuteOnFeedBack |
Retrieve the mute on state for the specified microphone.
(Inherited from MicrophoneBase) | |
| Name |
Get or Set the name of this microphone. This will modify the return value of the ToString method.
(Inherited from MicrophoneBase) | |
| NominalFeedBack | Indicates that the mic signal level has exceeded the nominal level. The nominal indication is reported when the incoming mic signal is between -10dBFS and -30dBFS. | |
| Owner |
Switcher that owns this Microphone
(Inherited from MicrophoneBase) | |
| PhantomPowerOffFeedBack | Indicates that phantom power has been disabled. | |
| PhantomPowerOnFeedBack | Indicates that phantom power has been enabled. | |
| VuFeedBack | Reports the VU meter feedback value (volume of the audio source), when VU feedback is enabled. Reported values will range from 0 to 8. |