Click or drag to resize

Dmps3AudioOutputEqualizer Properties

The Dmps3AudioOutputEqualizer type exposes the following members.

Properties
 NameDescription
Public propertyBass Adjusts the bass settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.
Public propertyBassDown Decrease the bass level of the specified output.
Public propertyBassFeedback Returns the current bass settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.

The DMOutputChange event will trigger with BassFeedbackEventId.

Public propertyBassUp Increase the bass level of the specified output.
Public propertyEqualizerType The type of equalizer available.
(Inherited from OutputEqualizerBase)
Public propertyGeqGain125Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 125Hz frequency band.
Public propertyGeqGain125HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 125Hz frequency band.

The DMOutputChange event will trigger with GeqGain125HzFeedbackEventId.

Public propertyGeqGain16KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 16KHz frequency band.
Public propertyGeqGain16KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 16KHz frequency band.

The DMOutputChange event will trigger with GeqGain16KHzFeedbackEventId.

Public propertyGeqGain1KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 1KHz frequency band.
Public propertyGeqGain1KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 1KHz frequency band.

The DMOutputChange event will trigger with GeqGain1KHzFeedbackEventId.

Public propertyGeqGain250Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 250Hz frequency band.
Public propertyGeqGain250HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 250Hz frequency band.

The DMOutputChange event will trigger with GeqGain250HzFeedbackEventId.

Public propertyGeqGain2KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 2KHz frequency band.
Public propertyGeqGain2KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 2KHz frequency band.

The DMOutputChange event will trigger with GeqGain2KHzFeedbackEventId.

Public propertyGeqGain315Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 31.5Hz frequency band.
Public propertyGeqGain315HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 31.5Hz frequency band.

The DMOutputChange event will trigger with GeqGain315HzFeedbackEventId.

Public propertyGeqGain4KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 4KHz frequency band.
Public propertyGeqGain4KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 4KHz frequency band.

The DMOutputChange event will trigger with GeqGain4KHzFeedbackEventId.

Public propertyGeqGain500Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 500Hz frequency band.
Public propertyGeqGain500HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 500Hz frequency band.

The DMOutputChange event will trigger with GeqGain500HzFeedbackEventId.

Public propertyGeqGain63Hz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 63Hz frequency band.
Public propertyGeqGain63HzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 63Hz frequency band.

The DMOutputChange event will trigger with GeqGain63HzFeedbackEventId.

Public propertyGeqGain8KHz Adjusts the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 8KHz frequency band.
Public propertyGeqGain8KHzFeedback Reports the gain of the graphic equalizer from -120 (-12dB) to +120 (+12db) at the 8KHz frequency band.

The DMOutputChange event will trigger with GeqGain8KHzFeedbackEventId.

Public propertyLimiterAttack Sets the attack time, which is the time in milliseconds that it takes the limiter to start clipping the signal level after the threshold has been exceeded. Valid values range from 1 (0.1ms) to 3000 (300ms).
Public propertyLimiterAttackFeedback Retrieves the attack time, which is the time in milliseconds that it takes the limiter to start clipping the signal level after the threshold has been exceeded. Valid values range from 1 (0.1ms) to 3000 (300ms).

The DMOutputChange event will trigger with LimiterAttackFeedbackEventId.

Public propertyLimiterDisableFeedback Indicates that limiting is disabled.
Public propertyLimiterEnableFeedback Indicates that limiting is enabled.
Public propertyLimiterHold Not supported on the DMPS3's Audio Output.
Public propertyLimiterHoldFeedback Not supported on the DMPS3's Audio Output.
Public propertyLimiterRatio Sets the limiter ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. Valid values range from 1 (1:1) to 10 (10:1).
Public propertyLimiterRatioFeedback Retrieves the limiter ratio, which controls the amount of gain reduction to apply when the mic signal level exceeds the threshold. Valid values range from 1 (1:1) to 10 (10:1).

The DMOutputChange event will trigger with LimiterRatioFeedbackEventId.

Public propertyLimiterRelease Sets the release time, which is the time over which the limiter will stop clipping after the signal crosses under the threshold. Valid values range from 1 (1ms) to 1000 (1000ms)
Public propertyLimiterReleaseFeedback Retrieves the release time, which is the time over which the limiter will stop clipping after the signal crosses under the threshold. Valid values range from 1 (1ms) to 1000 (1000ms)

The DMOutputChange event will trigger with LimiterReleaseFeedbackEventId.

Public propertyLimiterSoftKneeOffFeedback Indicates that soft knee limiting is disabled. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
Public propertyLimiterSoftKneeOnFeedback Indicates that soft knee limiting is enabled. When soft knee limiting is enabled, this signifies that limiting will be applied gradually, depending on how far the signal is from the threshold. The slower onset can make the limiting less noticeable, especially when using high compression ratios. When soft knee limiting is disabled, this will apply normal (hard knee) limiting. This signifies that as soon as the signal exceeds the threshold, it is clipped immediately to the threshold.
Public propertyLimiterThreshold Sets the limiting threshold. Valid values range from -800 (-80dB) to 0 (0dB) Once the signal exceeds the threshold, the limiter will clip the level to the threshold value. In this way, the output signal level will never exceed the threshold.
Public propertyLimiterThresholdFeedback Retrieves the limiting threshold. Valid values range from -800 (-80dB) to 0 (0dB) Once the signal exceeds the threshold, the limiter will clip the level to the threshold value. In this way, the output signal level will never exceed the threshold.

The DMOutputChange event will trigger with LimiterThresholdFeedbackEventId.

Public propertyParent The parent that a given object was added to.
(Inherited from OutputEqualizerBase)
Public propertyTreble Adjusts the treble settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.
Public propertyTrebleDown Decrease the treble level of the specified output.
Public propertyTrebleFeedback Returns the current treble settings for the specified output. Valid values range from -180 (-18dB) to 180 (+18dB). A value of 0 signifies a flat level corresponding to 0dB.

The DMOutputChange event will trigger with TrebleFeedbackEventId.

Public propertyTrebleUp Increase the treble level of the specified output.
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from OutputEqualizerBase)
Top
See Also