Dge |
The Dge2TouchOutReservedSigs type exposes the following members.
| Name | Description | |
|---|---|---|
| BooleanInput |
Bool Inputs on the device extender.
(Inherited from DeviceExtender) | |
| BooleanOutput |
Bool Outputs on the device extender.
(Inherited from DeviceExtender) | |
| ChannelBnc1 | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelBnc2 | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelComposite |
Specifies the target pad area.
Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of
pad areas the target supports differs depending on the panel.
Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8).
(Inherited from DgeTouchOutReservedSigs) | |
| ChannelHdmi1 | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelHdmi2 | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelSvid |
Specifies the target pad area.
Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number
of pad areas the target supports differs depending on the panel.
Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8).
(Inherited from DgeTouchOutReservedSigs) | |
| ChannelVga1Component | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelVga1Rgb | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelVga2Component | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelVga2Composite | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelVga2Rgb | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelVga2Svid | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| ChannelWhiteboard | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| DestinationBnc1 | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationBnc2 | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationComposite |
Sets the destination for the touch output.
Valid analog values range from 2d to 254d as follows:
2d = Cresnet
3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the DGE.)
Out of range values are ignored.
(Inherited from DgeTouchOutReservedSigs) | |
| DestinationHdmi1 | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationHdmi2 | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationSvid |
Sets the destination for the touch output.
Valid analog values range from 2d to 254d as follows:
2d = Cresnet
3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the DGE.)
Out of range values are ignored.
(Inherited from DgeTouchOutReservedSigs) | |
| DestinationVga1Component | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationVga1Rgb | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationVga2Component | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationVga2Composite | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationVga2Rgb | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationVga2Svid | Sets the destination for the touch output. Valid analog values range from 2d to 254d as follows: 2d = Cresnet 3d to 254d = Ethernet Device ID (this value should match the Device ID entered in the IP Table of the panel.) Out of range values are ignored. | |
| DestinationWhiteboard | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| FormatBnc1 | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatBnc2 | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatComposite |
Sets the touch output format of the VIDEO IN source to "Touch the PC V2" format.
Valid values are:
3d = UPDD XP Driver
6d = Remote Annotation Driver
(Inherited from DgeTouchOutReservedSigs) | |
| FormatHdmi1 | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatHdmi2 | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatSvid |
Sets the touch output format of the VIDEO IN source to "Touch the PC V2" format.
Valid values are:
3d = UPDD XP Driver
6d = Remote Annotation Driver
(Inherited from DgeTouchOutReservedSigs) | |
| FormatVga1Component | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatVga1Rgb | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatVga2Component | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatVga2Composite | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatVga2Rgb | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatVga2Svid | Sets the touch output format of the video source to "Touch the PC V2" format. Valid values are: 3d = UPDD XP Driver 6d = Remote Annotation Driver | |
| FormatWhiteboard | Specifies the target pad area. Pad areas are enabled in the Design tab of the properties for a Video object in VTPro-e. The number of pad areas the target supports differs depending on the panel. Valid values range from 0d (Pad Area 1) to 7d (Pad Area 8). A value of 0d should be used for a PC cursor using the "UPDD XP Driver" format. | |
| StringInput |
String Inputs on the device extender.
(Inherited from DeviceExtender) | |
| StringInputSigCompositeFeedback |
The mouse command StringInputSig which the control system routes to the external PC via the
control system's COM port.
(Inherited from DgeTouchOutReservedSigs) | |
| StringInputSigSvidFeedback |
The mouse command StringInputSig which the control system routes to the external PC via the control system's COM port.
(Inherited from DgeTouchOutReservedSigs) | |
| StringOutput |
String Outputs on the device extender.
(Inherited from DeviceExtender) | |
| StringOutputSigBnc1Feedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigBnc2Feedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigHdmi1Feedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigHdmi2Feedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga1ComponentFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga1CompositeFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga1RgbFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga1SvidFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga2ComponentFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga2CompositeFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga2RgbFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| StringOutputSigVga2SvidFeedback | The mouse command string which the control system routes to the PC via the control system's COM port. | |
| UShortInput |
UShort Inputs on the device extender.
(Inherited from DeviceExtender) | |
| UShortOutput |
UShort Outputs on the device extender.
(Inherited from DeviceExtender) |