Click or drag to resize

Dmps3AudioOutputMixer Properties

The Dmps3AudioOutputMixer type exposes the following members.

Properties
 NameDescription
Public propertyDelay Sets the delay level. Valid values range from 0 (0ms) to 850 (85ms).
Public propertyDelayFeedback Reports the current delay level. Valid values range from 0 (0ms) to 850 (85ms).

The DMOutputChange event will trigger with DelayFeedBackEventId.

Public propertyMaxVolume Specifies the maximum volume gain, in tenths of a dB. The MinVolume and MaxVolume properties allow endpoints to be set for volume control. Typically, this property would not be used since the minimum volume can be set through the Front Panel Setup Menus or using the DM Tool in Toolbox. Valid values range from -300 (-30dB) to 100 (10dB).
Public propertyMaxVolumeFeedback Reports the current maximum volume gain, in tenths of a dB. Valid values range from -300 (-30dB) to 100 (10dB).

The DMOutputChange event will trigger with MaxVolumeFeedBackEventId.

Public propertyMicLevel Property to set the value of the level for a given microphone on this output.
Public propertyMicLevelDown Decrease the Microphone level for a given microphone as long as the sig is true.
Public propertyMicLevelFeedback Property to read the feedback level for a given microphone on this output.

The DMOutputChange event will trigger with Mic1LevelFeedBackEventId.

Public propertyMicLevelUp Increase the Microphone level for a given microphone as long as the sig is true.
Public propertyMicMuteOffFeedback Property to return the state of the MicMuteOffFeedback for a given microphone on this output.

The DMOutputChange event will trigger with Mic1MuteOffFeedBackEventId.

Public propertyMicMuteOnFeedback Property to return the state of the MicMuteOnFeedback for a given microphone on this output.

The DMOutputChange event will trigger with Mic1MuteOnFeedBackEventId.

Public propertyMicPan Property to set the value of the pan for a given microphone on this output.
Public propertyMicPanFeedback Property to read the pan level for a given microphone on this output.

The DMOutputChange event will trigger with Mic1PanFeedBackEventId.

Public propertyMinVolume Specifies the minimum volume gain, in tenths of a dB. The MinVolume and MaxVolume properties allow endpoints to be set for volume control. Typically, this property would not be used since the minimum volume can be set through the Front Panel Setup Menus or using the DM Tool in Toolbox. Valid values range from -800 (-80dB) to -400 (-40dB).
Public propertyMinVolumeFeedback Reports the current minimum volume gain, in tenths of a dB. Valid values range from -800 (-80dB) to -400 (-40dB).

The DMOutputChange event will trigger with MinVolumeFeedBackEventId.

Public propertyMixerBypassedFeedback Indicates that the routed audio input is in mixer bypass mode. Mixer bypass mode allows advanced audio to pass through the HDMI switch. The DMPS3 mixers only support stereo PCM. On digital outputs, this means that the audio is routed directly from the audio source without passing through the mixer. The microphone mix and audio controls are not available. On analog outputs the selected source audio will be muted. Mixer bypass mode is only controllable via the DMPS Tool.

The DMOutputChange event will trigger with MixerBypassedFeedBackEventId.

Public propertyMonoOutputFeedback Indicates that the DM output is in mono. The output remains true for as long as mono mode is active. This output will be asserted whether mono mode is enabled via MonoOutput() method or if the Program Output is set to 70V/100V mode.
Public propertyOutputMixerType The type of Output Mixer available. See the definition of IOutputMixer interface for more information.
(Inherited from OutputMixerBase)
Public propertyOutputVuFeedback Reports the VU meter feedback value, when VU feedback is enabled. Reported values will range from 0 to 8.

The DMOutputChange event will trigger with OutputVuFeedBackEventId.

Public propertyParent The parent that a given object was added to.
(Inherited from OutputMixerBase)
Public propertyStartupVolume Specifies the startup volume in tenths of a dB. The startup volume is the volume level that will be set when the system is turned on. Valid values range from -800 (-80dB) to 100 (10dB).
Public propertyStartupVolumeFeedback Reports the current startup volume in tenths of a dB. Valid values range from -800 (-80dB) to 100 (10dB).

The DMOutputChange event will trigger with StartupVolumeFeedBackEventId.

Public propertyStereoOutputFeedback Indicates that the DM output is in stereo. The output remains true for as long as stereo mode is active.
Public propertyUserSpecifiedObject Can be assigned anything that user wants.
(Inherited from OutputMixerBase)
Top
See Also